Buell Ecm Cable Driver

The shipping cost, may be, in some instances, included as part of the item cost, and as such, may not be displayed as a separate cost or line item. Please use your favourite search engine to find vendors. The entire assembly procedure takes approximately five minutes. At this point the configuration of the Bluetooth modem is done and it's now available for the EcmSpy software. Click picture for an unscaled view.

Here again is the back of the finished plug and the correct position of the individual cable colors. Some Bluetooth modems need only a drop of solder applied to a small pad to connect these two lines. The Bluetooth modem now has the power supply attached, a bit of veroboard with a voltage regulator.

Write a review

Here is a good place to start your search. Be careful how these are inserted as this will determine the pin-out of the final plug. Any permission granted herein terminates automatically without further notice if you breach any of the above terms.

The last step is to press the clip from the front into the plug. If this message is displayed, the cable can be safely assumed to work properly. The pin numbers are stamped on the wire backward side of the plug housing.

We've recently launched our new Support Portal at support. Click image for an unscaled view. This will keep the contacts in place in the event that the plug is separated and locks the contacts into the plug so they will hold the plug seal in position. Ensure that the clip housing engages completely into the plug. Part is in good working condition.

It is in excellent working condition. Only some of the listed competitors provide a protective hood which should be considered a requirement by the buyer. Recovery and re-installation of software programs and user data are not covered under this Limited Warranty. You will often find cheap EcmSpy cables offered in the internet.

This effectively doubles the gauge of the wire and ensures a tight fit. Any and all Personal Information that is provided may be protected under federal regulations.

Other websites to which we may provide links, may be governed by different policies. You will need to ensure the product s are returned with any and all inclusions and accessories and in good physical condition no scratches such that the product is resale-ready.

For other brands please consult the Bluetooth modem's user guide. All Products are made in North America.

Crimping could be done with a allmost any heavy duty crimping pliers e. Unfortunately the voltage supply at the DataLink connector is too high for these modules, but with a cheap voltage regulator e. At the point of collection, you will be informed that your personal information is being collected, the purpose for which it is being collected and that you have a right of access to the information.

EcmSpy Cable for PC/Laptop

Upon such termination, you agree to immediately destroy any downloaded or printed materials. This information is aggregated with all other visitor information. Now insert the seal and contacts together into the plug body.

This material is meant for building battery packs and hardens after cooling. Heat the center of the connector with the iron until hot, then feed in the solder for a strong joint.

Then, slide the contacts over the cable and crimp or solder. None of the listed competitors build their own cables from scratch. Click image for an unscaled view Here again is the back of the finished plug and the correct position of the individual cable colors. If the contacts have been assembled in a wrong position, then the orange clip can be pulled out of the plug body and the contact unlocked of with a needle or small screwdriver. If necessary, the Bluetooth driver software has to be installed now, mb officecenter 115 driver according to the manufacturer's instructions.

We use Deutsch brand mating connectors because Buell and Harley Davidson provide Deutsch mating connectors. This is a new cdi unit off a Buell Cyclone. It should work on many Buell carbureted models.

This item is in good shape with normal wear and tear and is ready to be installed. Click image for an unscaled view The last step is to press the clip from the front into the plug.

This warranty does not apply to a Product or part of the Product that has been altered or modified e. Simply fill in the form below and one of our Team members will contact you promptly. None of the listed competitors provide a Shielded solution. The voltage adaptor shown is the size of a postage stamp.

EcmSpy wireless connection with Bluetooth

Cable drivers and virtual serial ports can create a lot of problems and troubleshooting them will often need a considerable amount of your time. Make sure the wire and connector are throughly cleaned with denatured alcohol to minimize contamination. These items may have minor cosmetic issues scratches, etc.

Buell Cables

Command mode remains active until the Bluetooth modem is switched off or rebooted. Make certain that the contacts are pushed completely through until they contact the front of the housing. This warranty does not apply to any defect or failure other than a manufacturing defect and or a manufacturing defect causing a failure of the intended performance.

Making our products available through our online Shop, Ebay and Amazon, has shown us that a single-point Support Portal would serve our Customers, better in every way. Use, duplication, or disclosure is subject to restrictions as set forth in applicable laws and regulations. The correct sequence is shown below all positions listed are viewed from the back with the clip facing up. If necessary, use a bent paper clip pushed through the back of the plug to help. Using your Android phone or tablet you can do the following All you need is this interface and an Android device.

Basic Black - Buell Motorcycle ECM to USB Tuning Cable With EAS Technology

Basic Black - Buell Motorcycle ECM to USB Tuning Cable With EAS TechnologyBUELL ECM CABLE BUYER S GUIDE by ecmcables - Issuu